Differences

This shows you the differences between two versions of the page.

--- mono3z2_dlp_3d_printer_visible_light [2022/08/24 21:46] – created jmuruena
+++ mono3z2_dlp_3d_printer_visible_light [2024/10/10 17:20] (current) – [Safety Concerns] mbates
@@ Line 1: / Line 1: @@
-====== Zeiss Inverted Microscope ======
+====== Mono3Z2 - Panchromatic Printer ======
 ^             Mono3Z2                              ^
-{{:mono3z2_.png?400|}}
+|{{:mono3z2_.png?400}}|
-| **Tool Type:**                  "Panchromatic Printer"                           |
+| **Tool Type:**                  Panchromatic Printer                           |
-| **Location:**                   "Elings Hall 2436"                           |
+| **Location:**                   Elings Hall 2436                           |
+| **Manufacturer:**               MonoPrinter                          |
-|  **Supervisor**        |  **Tool Lead**  |
-|  Juan Manuel Urueña    |  "WW Name"  |
-|  jmuruena@ucsb.edu  |  "WW Email"  |
-| **Description:**                "Panchromatic Printer"|
+|  **Principal Scientist**        |
-| **Manufacturer:**               "Mono3Z2"                           |
+|  Juan Manuel Urueña    |
+|  jmuruena@ucsb.edu  |
 ----
@@ Line 30: / Line 29: @@
 ----
 ===== Manuals =====
-{{ ::gradient_mnwr-s01-job_file_structure.pdf |}}
+{{ ::gradient_mnwr-s01-job_file_structure.pdf |MonoWare Job File
-{{ :mn3z-c01a-mono3z2_assembly.pdf |}}
+Structure}}\\
-{{ :mn3z-c01c-mono3z4_assembly.pdf |}}
+{{ :mn3z-c01a-mono3z2_assembly.pdf | MONO3Z2 (2CH) Initial Assembly & Alignment}}\\
-{{ :mn3z-c02-mono3z_printer_firmware.pdf |}}
+{{ :mn3z-c01c-mono3z4_assembly.pdf | MONO3Z4 (4CH) Initial Assembly & Alignment}}\\
-{{ :mn3z-c04-mono3z_first_printing.pdf |}}
+{{ :mn3z-c02-mono3z_printer_firmware.pdf |MONO3Z Series Printer Firmware}}\\
-{{ :mn3z-c05-mono3z2_led_swapping.pdf |}}
+{{ :mn3z-c04-mono3z_first_printing.pdf | Mono3Z First Printing}}\\
-{{ :mn3z-c08-mono3z4_4ch_printing.pdf |}}
+{{ :mn3z-c05-mono3z2_led_swapping.pdf |MONO3Z2 LED Swapping}}\\
-{{ :mn3z-c12-mono3z2_wiper_heater.pdf |}}
+{{ :mn3z-c08-mono3z4_4ch_printing.pdf |MONO3Z4 (4CH) Printing File}}\\
+{{ :mn3z-c12-mono3z2_wiper_heater.pdf |MONO3Z2 (2CH) Wiper & Heater}}\\
-----
-===== Plate Layout Template =====
-well plate experiment layout{{ :96_well_plate_layout.pdf |}}
 ----
 ===== Safety Concerns =====
-Read the manufactures manual before first use. If the MOno3Z2 acts in a way that is not described by the manual, turn off the printer and contact Mono at info@monoprinter.com .\\
+Read the manufactures manual before first use. If the Mono3Z2 acts in a way that is not described by the manual, turn off the printer and contact the principal scientist as well as Mono at info@monoprinter.com .\\
-	* Never place your finger near the machine until all parts have stopped moving. Moving parts can cause serious injury\\
+	* Never place your finger near the machine until all parts have stopped moving. Moving parts can cause serious injury.\\
-	* Never clean or service the printer while it is on\\
+	* Never clean or service the printer while it is on.\\
-	* The printer uses different LEDS. Never look directly at LED light nor expose skin. Serious injury may result from exposure\\
+	* The printer uses different LEDS. Never look directly at LED light nor expose skin. Serious injury may result from exposure.\\
-	* Disassembling the printer may cause an electric shock or damage to the instrument.    Do not disassemble any parts of the printer not mentioned in the instruction manual.    In case of a problem with the printer\\
+	* Disassembling the printer may cause an electric shock or damage to the instrument.    Do not disassemble any parts of the printer not mentioned in the instruction manual.\\
 ----