Differences

This shows you the differences between two versions of the page.

--- workshop_wizard_handbook [2020/02/10 08:54] – lemieux
+++ workshop_wizard_handbook [2021/01/22 18:36] (current) – furst
@@ Line 26: / Line 26: @@
   * **Rule of thumb:** Best to do in the mornings or weekends.
-. //Check and replenish hazardous waste labels//
+. //Check and replenish hazardous waste/waste labels//
+  - Empty solvent bottles should be rinsed, have their labels removed, and have a waste solvent label pre tagged.
+  - If waste bin is HALF full, [[https://hazwaste.ehs.ucsb.edu/HazWasteRequestDetail/93286417/244431_1-top|contact]] EH&S to schedule a waste pickup
 . //Check sharps containers//
   * If full, tape off the top and place in the hazardous waste bin.
@@ Line 111: / Line 112: @@
 **
-I) Check gloves: extra boxes are in microfluidics lab, write down what is taken on clipboard near the door.
+I) Check gloves: extra boxes are in microfluidics lab, write down what is taken on clipboard on the fume hood nearest to the exit.
 ) Check paper towels/WypAll: there is a dispenser above every sink and the key should already be in the dispenser.
@@ Line 143: / Line 144: @@
 ) Charge the camera battery: battery door is on bottom of camera and there is a wall charger in the fume hood.
-) Calibrate the scanner: follow the instructions on the computer
+) Calibrate the scanner:
+I) Go into the Einscan software on the desktop, then choose Einscan sp.
+II) Choose calibrate in the main interface.
+III) Place the Calibration stand on the turn-wheel and orient the calibration board (using the reference dots) on the stand as shown in the image on the software.
+IV) Press snap. Once complete, re-orient the board and snap again until the process is finished.
+   Note: The board and the stand can be found in the scanner fume hood.
 ) Turn off camera box light: the power button is on the side
@@ Line 167: / Line 172: @@
 ) When replacing the liners in the 3D printer cleaning fume hood, use the stock in the cabinet located to the lower left of the hood.
-) Fill out the IPA in the resin cleaner to the halfway point of the indicator.
+) Fill out the IPA in the resin cleaner to the halfway point of the indicator lines.
 Measure the specific gravity of the IPA in the cleaner. If the O-ring on the measuring device sits above the large flaps, replace the IPA.
 Reminder: Check the IPA level in the squirt bottles regularly.
@@ Line 174: / Line 179: @@
 ) Stratasys maintenance:
-a) Check the filament level, replace it with stock from the shelves in the corridor if necessary.
+a) Check the filament level, replace it with stock from the shelves in the corridor if necessary. (more details to be posted)
-b) To vacuum the printer, go to settings and bring the gantry up; preferably use gloves.
+b) To vacuum the print platform, go to settings and bring the gantry up; preferably use gloves.
 ) Miicraft maintenance: Remove the resin cover and mix the resin with a disposable pipette (found on the big, white box across the room) until the solution is homogeneous. Return the cover to protect from dust.
@@ Line 183: / Line 188: @@
 Note: This device is particularly dangerous. Wear gloves, coat, and face shield when opening the door. Ask Daniel or Mr. Bothman for detailed instructions.
 Note: The alarm may sound if the container is lowered too quickly. Silence the alarm with the button that is indicated with a warning light but do so only if you are certain that this was the cause of the alarm.
+-----
+==== Workshop Wizard Wiki Guide ====
+PLEASE ONLY EDIT IF YOU CAN IMPROVE A PAGE.
+{{:wiki:microfluidics_and_innovation_workshop_wiki_guide.pdf|}}