3d_print_water_jet_cleaning_station
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revision | |||
| 3d_print_water_jet_cleaning_station [2020/10/08 17:24] – [Reference Documentation] furst | 3d_print_water_jet_cleaning_station [2021/06/15 21:17] (current) – jmuruena | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== | + | ====== |
| - | ^ | + | ^ SMaLL Printer |
| - | | {{:tools: | + | {{:smallprinterschematic.jpg?400|}} |
| - | | **Tool Type: | + | | **Tool Type: |
| - | | **Location: | + | | **Location: |
| | **Supervisor** | | **Supervisor** | ||
| - | | | + | | |
| - | | (805) 893-4125 | + | | |
| - | | | + | |
| - | | **Description: | + | | **Description: |
| - | | **Manufacturer: | + | | **Manufacturer: |
| ---- | ---- | ||
| ===== About ===== | ===== About ===== | ||
| - | This waterjet cleaner is mainly used to clean the support material off Objet prints. Parts should typically be scraped clean with the waterjet cleaner only used to remove material in hard to reach areas and micropores within the RGD 450. | ||
| - | ---- | + | SMaLL is capable of creating unique structures with mechanically and chemically distinct |
| + | regions. By using tunable, visible wavelength photoswitches, | ||
| + | crosslinking reactions, a single resin formulation can be employed for the facile, one-step | ||
| + | printing of complex, bioinspired structures. The fabrication of soft joints and brick-and-motar | ||
| + | architectures showcase the utility of SMaLL for printing all-polymer composites with well-defined | ||
| + | regions for different mechanical and chemical properties. | ||
| - | =====Training===== | + | ---- |
| - | + | ||
| - | [[objet30trainingsop|Objet 30 Users Outline and SOP]] | + | |
| - | + | ||
| - | ----- | + | |
| ===== Detailed Specifications ===== | ===== Detailed Specifications ===== | ||
| - | * Water consumption: | ||
| - | * 85-88 dB when operating | ||
| + | * wavelength: 380 - 740 nm\\ | ||
| + | * luminous flux: 2,500 lumens\\ | ||
| + | * Projector: Epson PowerLite Home Cinema 5040UB\\ | ||
| + | * 1080p native resolution with 4K Enhancement\\ | ||
| - | ----- | + | ---- |
| ===== Safety Concerns ===== | ===== Safety Concerns ===== | ||
| - | * Lid should remain latched | + | |
| - | * Water should be shut off to the machine imminently after cleaning is finished | + | Read the manufactures manual before first use. If the BIO X Cellink acts in a way that is not described by the manual, turn off the printer |
| - | * Cracked protective gloves should imminently | + | * Never place your finger near the machine |
| - | * Do not operate water jet outside of sealed container | + | * Never clean or service the printer while it is on\\ |
| + | * The printer uses UV light for sterilization and curing. Never look directly at UV light nor expose skin. Serious injury may result from exposure\\ | ||
| + | * The printer has heated surfaces that can reach temperature up to 250 degrees Celsius. Never touch these surfaces when using the heating function. Allow things | ||
| + | * Always ensure that equipment is correctly mounted before use. Imporperly mounted print beds, printheads, cartridges, calbes liquid spouts and air spouts can be dangerous. If any equipment appears damaged, turn off the printer, unplug all connections and contact CELLINK. \\ | ||
| ---- | ---- | ||
| + | ===== Operating Procedures ===== | ||
| + | |||
| + | Insert Text Here! | ||
| + | |||
| + | ---- | ||
| ===== Reference Documentation ===== | ===== Reference Documentation ===== | ||
| - | {{ :tools: | + | |
| + | {{ :creationworkshop.pdf |}}\\ | ||
| + | {{ :small_projector_manual.pdf |}} | ||
| ----- | ----- | ||
| + | ===== Training Documentation ===== | ||
| + | {{ : | ||
| + | ---- | ||
3d_print_water_jet_cleaning_station.1602177854.txt.gz · Last modified: 2020/10/08 17:24 by furst