amp_led_uv-cube_ii
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| amp_led_uv-cube_ii [2022/05/27 21:54] – created jmuruena | amp_led_uv-cube_ii [2024/10/10 17:08] (current) – [Safety Concerns] mbates | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== UV Curing Oven ====== | ====== UV Curing Oven ====== | ||
| - | ^ | + | ^ |
| | {{: | | {{: | ||
| - | | **Tool Type: | + | | **Tool Type: |
| - | | **Location: | + | | **Location: |
| + | | **Manufacturer: | ||
| - | | **Supervisor** | | + | | **Principal Scientist** | |
| - | | Juan Manule Uruena | + | | Juan Manuel Urueña |
| - | | | (###) ### | + | | jmuruena@ucsb.edu |
| - | | jmuruena@ucsb.edu | + | |
| - | + | ||
| - | | **Description: | + | |
| - | | **Manufacturer: | + | |
| ---- | ---- | ||
| Line 21: | Line 18: | ||
| The UV curing oven is located in Elings Hall 2436. | The UV curing oven is located in Elings Hall 2436. | ||
| - | Some Carbon Resins used in the Form 2 3D printer can benefit from post process curing. Each resin has a specific hardening curve which can be found within the reference material which will indicate the ideal time and temperature to be set on the AMP UV curing oven. | + | Some Carbon Resins used in the Form 2 3D printer can benefit from post process curing. Each resin has a specific hardening curve which can be found within the reference material which will indicate the ideal time and temperature to be set on the APM UV curing oven. |
| - | + | ||
| - | ---- | + | |
| - | + | ||
| - | ===== Training Documentation ===== | + | |
| ---- | ---- | ||
| Line 33: | Line 25: | ||
| LED source: 365 nm\\ | LED source: 365 nm\\ | ||
| - | 32 mW/cm^2 center of upper tray\\ | + | |
| + | ^ Tray Position | ||
| + | | top | | ||
| + | | middle | ||
| + | | bottom | ||
| ---- | ---- | ||
| Line 40: | Line 36: | ||
| - | * Allow at least half an hour for IPA to evaporate before placing part in Form Cure | + | * Allow at least half an hour for IPA to evaporate before placing part in FormCure\\ |
| - | * Allow time for the Form Cure to cool off before removing parts | + | * Allow time for the FormCure |
| - | * Do not operate | + | * Do not operate |
| ---- | ---- | ||
| - | ---- | ||
| ===== Operating Proceduces ===== | ===== Operating Proceduces ===== | ||
| Line 55: | Line 50: | ||
| 5. Use the dial on the front of the FormCure to set time and temperature\\ | 5. Use the dial on the front of the FormCure to set time and temperature\\ | ||
| 6. Place part within the FormCure→ press start.\\ | 6. Place part within the FormCure→ press start.\\ | ||
| + | |||
| + | ----- | ||
| ===== Reference Documentation ===== | ===== Reference Documentation ===== | ||
| - | {{ : | + | {{ : |
amp_led_uv-cube_ii.1653688456.txt.gz · Last modified: 2022/05/27 21:54 by jmuruena