Differences

This shows you the differences between two versions of the page.

--- amp_led_uv-cube_ii [2022/05/27 21:55] – [Detailed Specifications] jmuruena
+++ amp_led_uv-cube_ii [2024/10/10 17:08] (current) – [Safety Concerns] mbates
@@ Line 1: / Line 1: @@
 ====== UV Curing Oven ======
-^                  AMP LED UV-Cube                  ^
+^                  APM LED UV-Cube                  ^
 |          {{:uvcuringoven.png?400|}}           |
-| **Tool Type:**                  "UV curing oven"                           |
+| **Tool Type:**                  UV Curing Oven                           |
-| **Location:**                   "Elings 2436"                           |
+| **Location:**                   Elings 2436                           |
+| **Manufacturer:**               APM                           |
-|  **Supervisor**        |  **Tool Lead**  |
+|  **Principal Scientist**        |
-|  Juan Manule Uruena         |  "WW Name"  |
+|  Juan Manuel Urueña    |
-|                        |  (###) ###-####  |
+|  jmuruena@ucsb.edu  |
-|  jmuruena@ucsb.edu  |  "WW Email"  |
-| **Description:**                "UV Curing Oven "                           |
-| **Manufacturer:**               "AMP"                           |
 ----
@@ Line 21: / Line 18: @@
 The UV curing oven is located in Elings Hall 2436.
-Some Carbon Resins used in the Form 2 3D printer can benefit from post process curing. Each resin has a specific hardening curve which can be found within the reference material which will indicate the ideal time and temperature to be set on the AMP UV curing oven.
+Some Carbon Resins used in the Form 2 3D printer can benefit from post process curing. Each resin has a specific hardening curve which can be found within the reference material which will indicate the ideal time and temperature to be set on the APM UV curing oven.
 ----
-===== Training Documentation =====
+===== Detailed Specifications =====
+LED source: 365 nm\\
-----
+^  Tray Position  ^  Power Setting  |
+|  top  |  32 mW/cm<sup>2</sup>  |
+|  middle  |  17 mW/cm<sup>2</sup>  |
+|  bottom  |  12 mW/cm<sup>2</sup>  |
-===== Detailed Specifications =====
-LED source: 365 nm\\
-**Power settings**\\
-mW/cm^2 upper tray\\
-mW/cm^2 middle tray\\
-mW/cm^2 bottom tray\\
 ----
@@ Line 42: / Line 36: @@
-*    Allow at least half an hour for IPA to evaporate before placing part in Form Cure
+*    Allow at least half an hour for IPA to evaporate before placing part in FormCure\\
-*    Allow time for the Form Cure to cool off before removing parts
+*    Allow time for the FormCure to cool off before removing parts\\
-*    Do not operate form cure with lid open
+*    Do not operate FormCure with lid open
 ----
-----
 ===== Operating Proceduces =====
@@ Line 57: / Line 50: @@
 . Use the dial on the front of the FormCure to set time and temperature\\
 . Place part within the FormCure→ press start.\\
+-----
 ===== Reference Documentation =====
-{{ :amp_led_uv-cube_ii.pdf |}}
+{{ :amp_led_uv-cube_ii.pdf | APM LED UV-Cube II User Manual}}