NSF BioPACIFIC MIP Wiki

A National User Facility Dedicated to Biomaterials

User Tools

Site Tools

Trace:
haas_super_mini_mill_training_sop

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
haas_super_mini_mill_training_sop [2020/09/28 16:20] – created fursthaas_super_mini_mill_training_sop [2021/03/11 19:53] (current) – furst
Line 99: Line 99:
     - Post the code by selecting Post Process and selecting Carbide 3D (grbl) as the post configuration. The program name or number should be numbers only, and is typically notated 00001 (not necessary for carbide but good practice for larger machines) make sure to select the desired output folder as by default Solidworks buries the G-code      - Post the code by selecting Post Process and selecting Carbide 3D (grbl) as the post configuration. The program name or number should be numbers only, and is typically notated 00001 (not necessary for carbide but good practice for larger machines) make sure to select the desired output folder as by default Solidworks buries the G-code 
  
-====Setting up the ShopBot for a Job:====  +====Setting up the Haas Mill for a Job:====  
-The ShopBot router uses slightly less puny ER20 collets to hold tools from .04" to .511" but typically uses tools with a 1/8, 3/16,1/4 or 1/2 inch shank. +The Haas CNC mill uses big boy CT 40 taper tools to hold anything from ER 32 collets to drill chucks and work piece probes. Gripping range is basically anything you can imagine machine with this tool all the way up to 1" shanks. Tool 1 is typically set up with a 1/2" endmills and tool 8 with a Renishaw tool probe.
  
 **Changing tools:** **Changing tools:**
-  - Turn the router off and using an acid brush remove metal shavings and any dust from the tool and collect +  - Select MDI mode by pressing the MDI/DNC button once 
-  - Using the large open wrench on the spindle shaft flats and the spanner on the collet nut, loosen the collet and tool. +  - Using the ATC forward and ATC reverse buttons bring the desired tool into the spindle  
-  - Unscrewing the nut all the way allows the collet and tool to be removed from the spindle and changed out with a different tool of the same shank diameter or with a different sized collet. +  - HOLDING THE TOOL HOLDER that is in the spindle press the ATC release button or the black button located on the machine head inside the machine 
-  - Separating the collet from the collet nut can be done by pushing on the back end of the collet so that it becomes angled within the retaining collet nut and then can be pulled out. +  - The tool should release with an accompanied air purge to clean the spindle tapers 
-  - Before reinstalling the new collet and tool, wipe down the tool shank as well as the collet and spindle tapper.+  - Using the CAT 40 tool tightening fixture in a vice, secure the tool holder insuring to close the lever containing the second spindle dog  
 +  - Using a spanner or a box wrench carefully loosen the collet nut or tool clamping mechanism 
 +  - Before replacing the cutting tool insure all collet tapers and tool shanks are clean and free from dust or chips. Wipe with a clean paper towel before installing 
 +  - Using the correct spanner or box wrench carefully and firmly tighten the collet nut or retaining mechanism.  
 +  - Check the pullstud with an open ended wrench and insure that it is snug within the Cat 40 tool holder 
 +  - Pressing and holding the ATC release button or black button on the head of the Haas insert the tool holder into the spindle making sure to align the spindle dogs with the tool holder before releasing the button.
  
 **Homing and Zeroing the machine:**  **Homing and Zeroing the machine:** 
-  - With the tool installed, make sure the bed is empty and the doors are closed before turning on the machine. The switch on the front of the machine should turn it on, however there are two different interlocks, one on the back of the machine which controls master power, and one on the hand unit which need a key before the machine will move. +  - 
-  - Launch ShopBot 3 from the laser cutter computer +
-  - Select the X,Y table button from the red position window to send the machine to its home position +
-  - With the tool in the spindle, attach the grouping clamp to the tool shank or the spindle, and place the aluminum electrode on top of stock you wish to cut. Jog the tool to be above the electrode. Check that as the tool and electrode come in contact that output one lights up. Select the Z button from the same position window and the machine will automatically zero out the tool height then retract to 1/2" above the surface. +
-  - Next select the yellow keypad to move the spindle to find part zero broad movements can be made using the arrows, fine adjustment can be made by pressing the "Fixed" button and entering a jog distance per click.  +
-    - An edge finder can be used at the minimum RPM to find the part X and Y zero by jogging using the virtual keypad. Offset the axis by the radius of the edge finder, and switch the console to advanced mode. Under the zero drop down select X or Y zero to set part zero. The cutting tool can then be replaced in the spindle and re-zeroed using the automatic tool length touch off.  +
-    - An alternative but fastest way to establish part zero is by using a piece of paper or shim and slowly jogging the axis towards the part until slight resistance is felt on the paper or shim used. The part zero can then be set after offsetting X and Y by the radius of the tool plus shim thickness, and the Z axis by shim thickness.  +
  
 **Starting Job:** **Starting Job:**
-  - Load the desired G-code using the File drop down and selecting "load new file" +  - 
-  - Make sure drawing zero matches machine part zero +
-  - Start Job +
 ====Machine Limitations==== ====Machine Limitations====
-  * Each tool change should be accompanied by a new job within HSM Works +  * 
-  * Tool shank diameter is limited to 13 mm +
-  * Max stepdown is limited to .05" in metal and .1" in wood +
-  * Work area is limited to 24" x 18" x 3.5" x,y,z+
    
  
 ====Choosing tools==== ====Choosing tools====
-Many tools are optimized for different materials, and although a 2 flute endmill can do most operations, it is not always ideal. Single and duel high helix endmills are available for plastics, woods, and composites, with carbide endmills and burs available for abrasive materials like glass fiber reinforced materials such as circuit boards.  +Many tools are optimized for different materials, and although a 2 flute endmill can do most operations, it is not always ideal. Single and duel flute high helix endmills are available for plastics, woods, and composites, with carbide endmills and burs available for abrasive materials like glass fiber reinforced materials such as circuit boards.  
-Feeds and speeds can be found {{ :tools:shopbotcncrouter:feedsandspeeds.pdf |HERE}}+Feeds and speeds can be found {{  |HERE}}
  
  
Line 145: Line 137:
  
 ----- -----
-=====Shopbot Desktop Quick Review=====+=====Haas Super Mini Mill Quick Review=====
 Tool Lead: Andrew Furst \\ Tool Lead: Andrew Furst \\
 Contact: Andrewfurst@ucsb.edu Contact: Andrewfurst@ucsb.edu
 ====Safety Concerns==== ====Safety Concerns====
   * Safety Glasses must be worn when machine is running   * Safety Glasses must be worn when machine is running
-  * The acrylic doors must be closed before starting a job+  * The glass door must be closed before starting a job
   * The spindle must be completely stopped before adjusting or removing work piece   * The spindle must be completely stopped before adjusting or removing work piece
   * After milling is completed, the work piece will have developed sharp burrs which must be removed with a hand file or sandpaper    * After milling is completed, the work piece will have developed sharp burrs which must be removed with a hand file or sandpaper 
haas_super_mini_mill_training_sop.1601310030.txt.gz · Last modified: 2020/09/28 16:20 by furst