Differences

This shows you the differences between two versions of the page.

--- keyence_sop [2020/11/12 18:21] – furst
+++ keyence_sop [2021/04/27 17:41] (current) – furst
@@ Line 11: / Line 11: @@
 !
-Name
+Name (Last, First)
 !
 Group or Company
 !
-Signature
+Signature (First, Last)
 |-
 |1
@@ Line 48: / Line 48: @@
 |}
 -----
 ====Overview:====
   * This training provides an introduction to using and operating the Keyence microscope including:
@@ Line 120: / Line 119: @@
   - **Software lighting and Image Quality**
     - Within Software lighting two tabs are available:
-      - Brightness \\ {{:tools:keyencemicroscope:lighting.jpg?400|}}
+      - Brightness \\ {{:tools:keyencemicroscope:lighting.png?400|}}
         - Adjust shutter speed and camera settings (set to auto)
-      - Lighting \\ {{:tools:keyencemicroscope:other_lighting.jpg?400|}}
+      - Lighting \\ {{:tools:keyencemicroscope:other_lighting.png?400|}}
         - Epi-illumination
           - Adjust/turn on internal objective illumination (press "light" on console to toggle)
@@ Line 133: / Line 132: @@
       - Select "depth up" from the right hand side bar then "quick composition and 3D"
       - Focus the microscope slightly below the lowest point on the object \\ {{:tools:keyencemicroscope:focuso_on_bottom.jpg?400|}}
-      - Click "3D Display" on the Keyence control pad and the microscope will scan up the object and create a 3D file which can be analyzed for depth. \\ {{:tools:keyencemicroscope:large_depth_of_field.jpg?400|}}{{:tools:keyencemicroscope:3d_depth_map.jpg?400|}}
+      - Click "3D Display" on the Keyence control pad and the microscope will scan up the object and create a 3D file which can be analyzed for depth. \\ {{:tools:keyencemicroscope:large_depth_of_field.jpg?400|}}{{:tools:keyencemicroscope:depth.png?400|}}
   - **Measure**
     - Measurements can be taken by selecting the "Measure" tab to measure the current view of the microscope or after a Depth up scan by selecting the "measure" tab after scan is complete
-      - Select the desired tool and desired points to measure from on the sample. The microscope will automatically display the length of lines or radius of arcs/circles drawn \\ {{:tools:keyencemicroscope:measuring.jpg?400|}}
+      - Select the desired tool and desired points to measure from on the sample. The microscope will automatically display the length of lines or radius of arcs/circles drawn \\ {{:tools:keyencemicroscope:measuring.png?400|}}
   - **Stitching**
-    - Center surround stitching \\ {{:tools:keyencemicroscope:stitch.jpg?400|}}
+    - Center surround stitching \\ {{:tools:keyencemicroscope:stitch.png?400|}}
       - Center the sample in the frame and select "stitching" from the sidebar
       - select "stitch around the current position"
       - click "Start stitching" and press enter to stop the stitching whenever the image collected reaches the desired size.
-    - Stitch after specifying the area \\ {{:tools:keyencemicroscope:stitch_set_bounds.jpg?400|}}
+    - Stitch after specifying the area \\ {{:tools:keyencemicroscope:stitch_set_bounds.png?400|}}
       - Click select range
       - Position the microscope as the minimum x position and select left, then maximum x position and select right