Differences

This shows you the differences between two versions of the page.

--- objet30pro [2020/02/20 21:23] – martinez
+++ objet30pro [2020/09/04 18:17] (current) – furst
@@ Line 1: / Line 1: @@
-====== Objet30Pro ======
+====== Stratasys Objet30 Pro Polyjet 3D Printer ======
-^             Stratasys Objet30Pro Polyjet 3D Printer                                   ^
+^             Stratasys Objet30 Pro Polyjet 3D Printer                                   ^
-|               {{ :tools:objet30pro.png?nolink&200 |}}                                 |
+|                    {{ :tools:objet30pro:objet30pro.png?nolink&200 |}}                 |
 | **Tool Type:**                  3D Printer                                            |
 | **Location:**              3430 Elings Hall (CNSI Microfluidics Lab)                  |
@@ Line 18: / Line 18: @@
 ===== About =====
 This 3D Printer is a very accurate and versatile tool that can be utilized with different types of printing materials. The printer has two print heads – one prints the structural material for parts, and the other prints a support material. Parts are built on a layer of the support material. Matt finish parts are surrounded in support, and overhanging features are supported with support material during printing. The support material is removed in the water jet station. This is a great tool for accurate and precise models.
+----
+===== Training Documentation =====
+[[Objet30TrainingSOP|Objet Training  SOP]]
 ----
@@ Line 55: / Line 61: @@
 ----
-===== Operating Procedures =====
+===== Reference Documentation =====
-__**Start of run:**__
+  * {{:tools:objet30pro:fathom_cleaning_polyjet_parts_with_sodium_hydroxide_2014.pdf|Cleaning Objet parts with Sodium Hydroxide}}
-  - Save CAD file in.STL format, bring to the printer on a thumb drive.
+  * {{:tools:objet30pro:microfluidicslab-making3d_printed_molds_.pdf|Making 3D printed Molds}}
-  - In //**Objet Studio insert**// the file – you should see the part on the image of the print platform.
+  * {{:tools:objet30pro:objet30postprinting.pdf|Post Processing}}
-  - **Validate** the design
+  * {{:tools:objet30pro:objet30userguide.pdf|Users Guide}}
-  - Select //**matt or glossy finish**// for each part
+Print Head Cleaning
-  - Run the **estimator** to determine the print materials required and the print time
+ {{ :tools:objet30pro:printheadcleaning_1_.mp4 |Print Head Cleaning}}
-  - Enter this information in the logbook
+Build Tray Cleaning 1
-  - Press **build**
+ {{ :tools:objet30pro:cleancoverglass_1_.mp4 |Build Tray Cleaning 1}}
-  - Open the remote desktop connection to the printer
+Build Tray Cleaning 2
-  - **In the printer window click on the red circle** – turning it green to start the job. At this point, you should hear the cooling fans on the printer turn on. The print job should start after the heads warm-up (~15 minutes if the printer hasn’t been running for a while).
+ {{ :tools:objet30pro:buildtraycleaning_2_.mp4 |Build Tray Cleaning 2}}
+Build Tray Cleaning 3
+ {{ :tools:objet30pro:buildtraycleaning_3_.mp4 |Build Tray Cleaning 3}}
+Head Allignment
+ {{ :tools:objet30pro:headalignment.mp4 |Head Allignment}}
+Load Cells Calibration
+ {{ :tools:objet30pro:loadcellscalibration_1_.mp4 |Load Cells Calibration }}
+Pattern Test
+ {{ :tools:objet30pro:patterntest_1_.mp4 |Pattern Test}}
+System Shutdown
+ {{ :tools:objet30pro:systemshutdown.mp4 |}}
+UV lamp Cleaning
+ {{ :tools:objet30pro:uvlampcleaning_1_.mp4 |UV lamp Cleaning}}
+Wiper Cleaning Inspection
+ {{ :tools:objet30pro:wipercleaninginspection_1_.mp4 |Wiper Cleaning Inspection}}
-__**After run is complete:**__
+-----
-  - Remove parts using a putty knife in the drawer below the printer.
-  - Scrape any support material remaining on the bed off with the razor scraper in the drawer beneath the printer. Take care to collect the debris, don’t dump it into the gap between the print bed and the printer.
-  - Clean the print bed using a paper towel wetted with water.
-  -** Run the head cleaning wizard – the print heads cost ~ $5k and will be ruined if not cleaned after the run!**
-  - Clean your parts in the water jet cleaner
-----
-===== Documentation =====
-Insert Text Here!
-----