objet30pro
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
objet30pro [2020/08/13 16:43] – [Training Documentation] furst | objet30pro [2020/09/04 18:17] (current) – furst | ||
---|---|---|---|
Line 18: | Line 18: | ||
===== About ===== | ===== About ===== | ||
This 3D Printer is a very accurate and versatile tool that can be utilized with different types of printing materials. The printer has two print heads – one prints the structural material for parts, and the other prints a support material. Parts are built on a layer of the support material. Matt finish parts are surrounded in support, and overhanging features are supported with support material during printing. The support material is removed in the water jet station. This is a great tool for accurate and precise models. | This 3D Printer is a very accurate and versatile tool that can be utilized with different types of printing materials. The printer has two print heads – one prints the structural material for parts, and the other prints a support material. Parts are built on a layer of the support material. Matt finish parts are surrounded in support, and overhanging features are supported with support material during printing. The support material is removed in the water jet station. This is a great tool for accurate and precise models. | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ===== Training Documentation ===== | ||
+ | |||
+ | [[Objet30TrainingSOP|Objet Training | ||
---- | ---- | ||
Line 52: | Line 58: | ||
* Several parts of the printer remain extremely hot even after it has stopped operating. Avoid touching the UV lamp and the print block. | * Several parts of the printer remain extremely hot even after it has stopped operating. Avoid touching the UV lamp and the print block. | ||
- | |||
- | ---- | ||
- | |||
- | ===== Operating Procedures ===== | ||
- | |||
- | __**Start of run:**__ | ||
- | - Save CAD file in.STL format, bring to the printer on a thumb drive. | ||
- | - In //**Objet Studio insert**// the file – you should see the part on the image of the print platform. | ||
- | - **Validate** the design | ||
- | - Select //**matt or glossy finish**// for each part | ||
- | - Run the **estimator** to determine the print materials required and the print time | ||
- | - Enter this information in the logbook | ||
- | - Press **build** | ||
- | - Open the remote desktop connection to the printer | ||
- | - **In the printer window click on the red circle** – turning it green to start the job. At this point, you should hear the cooling fans on the printer turn on. The print job should start after the heads warm-up (~15 minutes if the printer hasn’t been running for a while). | ||
- | |||
- | __**After run is complete: | ||
- | - Remove parts using a putty knife in the drawer below the printer. | ||
- | - Scrape any support material remaining on the bed off with the razor scraper in the drawer beneath the printer. Take care to collect the debris, don’t dump it into the gap between the print bed and the printer. | ||
- | - Clean the print bed using a paper towel wetted with water. | ||
- | -** Run the head cleaning wizard – the print heads cost ~ $5k and will be ruined if not cleaned after the run!** | ||
- | - Clean your parts in the water jet cleaner | ||
---- | ---- | ||
Line 79: | Line 63: | ||
===== Reference Documentation ===== | ===== Reference Documentation ===== | ||
- | * {{: | + | * {{: |
- | * {{: | + | * {{: |
- | * {{: | + | * {{: |
+ | * {{: | ||
+ | Print Head Cleaning | ||
+ | {{ : | ||
+ | Build Tray Cleaning 1 | ||
+ | {{ : | ||
+ | Build Tray Cleaning 2 | ||
+ | {{ : | ||
+ | Build Tray Cleaning 3 | ||
+ | {{ : | ||
+ | Head Allignment | ||
+ | {{ : | ||
+ | Load Cells Calibration | ||
+ | {{ : | ||
+ | Pattern Test | ||
+ | {{ : | ||
+ | System Shutdown | ||
+ | {{ : | ||
+ | UV lamp Cleaning | ||
+ | {{ : | ||
+ | Wiper Cleaning Inspection | ||
+ | {{ : | ||
- | ===== Training Documentation ===== | + | ----- |
- | {{ : | ||
- | [[Objet30TrainingSOP|Objet Training | ||
- | |||
- | ---- | ||
objet30pro.1597337025.txt.gz · Last modified: 2020/08/13 16:43 by furst