NSF BioPACIFIC MIP Wiki

A National User Facility Dedicated to Biomaterials

User Tools

Site Tools

Trace:
rayjet_300

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
rayjet_300 [2020/08/03 19:09] – [Reference Documentation] furstrayjet_300 [2020/08/31 18:46] (current) – [Reference Documentation] furst
Line 15: Line 15:
 | **Manufacturer:**               "Trotec"                           | | **Manufacturer:**               "Trotec"                           |
  
-----+-----
  
 ===== About ===== ===== About =====
Line 22: Line 22:
  
 ---- ----
 +===== Training Documentation =====
 +[[laser_cutter_training_sop|Laser Cutter Training SOP]]
  
 +----
 ===== Detailed Specifications ===== ===== Detailed Specifications =====
  
Line 34: Line 37:
  
 Looking directly into the laser can cause retinal damage. Confirm that the fume collection system is running whenever the laser is cutting or engraving. See list of approved materials for laser cutting, some require nitrogen gas if flammable, or could release chlorine gas if cut. NO NOT CUT NON APPROVED MATERIALS INCLUDING METALS. Laser lenses must be cleaned within ONE WEEK of time of use. If lenses has not been cleaned, clean before use to avoid damaging lenses.  Looking directly into the laser can cause retinal damage. Confirm that the fume collection system is running whenever the laser is cutting or engraving. See list of approved materials for laser cutting, some require nitrogen gas if flammable, or could release chlorine gas if cut. NO NOT CUT NON APPROVED MATERIALS INCLUDING METALS. Laser lenses must be cleaned within ONE WEEK of time of use. If lenses has not been cleaned, clean before use to avoid damaging lenses. 
- 
----- 
- 
-===== Operating Procedures ===== 
- 
-  - Turn on laser cutter and fume extractor 
-  - Use focusing tool to set bed height based on workpiece, move laser to desired starting position 
-  - Launch CorelDraw and import 2D sketch as PDF or DXF. Take the time to check scale using built in page rulers 
-  - Set lines to be cut as RED and patterns to be engraved as BLACK. (must use true RGB red and black) 
-  - Select Print -> Print settings  
-  - Within Print settings select desired laser recipe based on material and thickness, verify one click print is turned off, print order is set to inner features first, and import dimensions from CorelDraw is selected 
-  - Click Print  
-  - Navigate to Trotec software 
-  - Check Scale, do a dry run without laser power if necessary 
-  - Send job to laser cutter 
  
 ---- ----
Line 55: Line 43:
 [[Laser cutting data]] [[Laser cutting data]]
  
-{{:tools:rayjet300:rayjet-300_8024_operationmanual_en.pdf|}}+{{:tools:rayjet300:rayjet-300_8024_operationmanual_en.pdf|Operations Manual}}
  
-{{:tools:rayjet300:rayjet_8015_software-manual_en.pdf|}}+{{:tools:rayjet300:rayjet_8015_software-manual_en.pdf|Software Manual}}
  
-{{:tools:rayjet300:exhaust_system_information.pdf|}}+{{:tools:rayjet300:exhaust_system_information.pdf|Exhaust System Info}} 
 + 
 +{{:tools:rayjet300:rayjet_laser_cutter_notes.pdf|Laser Cutter Notes}}
  
-===== Training Documentation ===== 
  
-{{:tools:rayjet300:trotec_laser_training_r0.6.docx|}} 
  
-{{:tools:rayjet300:rayjet_laser_cutter_notes.pdf|}} 
  
-{{:tools:rayjet300:workshop_wizard_project_information_form_-_updated_laser_cutter_sop.pdf|}} 
  
-{{:tools:rayjet300:trotec_and_rayjet_training_sign_in.pdf|}} 
  
-{{:tools:rayjet300:trotec_rayjet_sop.pdf|}} 
----- 
  
rayjet_300.1596481789.txt.gz · Last modified: 2020/08/03 19:09 by furst