ultimaker_3_sop
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| ultimaker_3_sop [2020/08/26 19:14] – furst | ultimaker_3_sop [2021/04/27 17:40] (current) – furst | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ====== Training SOP====== | + | ======FDM Training SOP====== |
| Last edited: Furst (08/26/20) | Last edited: Furst (08/26/20) | ||
| Line 10: | Line 10: | ||
| ! | ! | ||
| - | Name | + | Name (Last, First) |
| ! | ! | ||
| Group or Company | Group or Company | ||
| ! | ! | ||
| - | Signature | + | Signature |
| |- | |- | ||
| |1 | |1 | ||
| Line 46: | Line 46: | ||
| | | | | ||
| |} | |} | ||
| + | ----- | ||
| ====Overview: | ====Overview: | ||
| - | * This training provides an introduction to the FDM 3D printers | + | * This training provides an introduction to using and operating |
| * File Types | * File Types | ||
| * Software | * Software | ||
| Line 59: | Line 59: | ||
| * Changing Fulfillment Type | * Changing Fulfillment Type | ||
| * Cleaning | * Cleaning | ||
| - | * Two printers (Ultimaker and F270) are both set up with ABS by default, Other materials are available upon request. | + | * The two FDM printers (Ultimaker and F270) are both set up to print with with ABS by default, Other materials are available upon request. |
| * Work by extruding thermoplastic filament onto build platform-Build the part layer by layer. | * Work by extruding thermoplastic filament onto build platform-Build the part layer by layer. | ||
| * Remember to enter job information into the 3D print job log! | * Remember to enter job information into the 3D print job log! | ||
| Line 69: | Line 69: | ||
| ====Job Setup==== | ====Job Setup==== | ||
| - | * Load your file into the print software on the computer adjacent to the printer (Cura for Ultimaker, GrabCad Print for F270). | + | |
| - | * Ultimaker: make sure print bed is clean | + | -Load your STL file into the print software on the computer adjacent to the printer (Cura for Ultimaker, GrabCad Print for F270). |
| - | * F270 make sure that there is enough room on an unwed build tray for your part, and that the build tray is secured | + | - Set Print Parameters: |
| - | * Set print parameters | + | - Position the part on the build tray in a way that is conducive to 3D printing (flat side down, minimize overhangs etc..) |
| - | | + | - Select appropriate layer or slice height (the more slices |
| - | * Send the job to the printer | + | - For Ultimaker: |
| - | | + | - Select " |
| + | - Check appropriate filament and bed temperatures | ||
| + | - Send job to Ultimaker using USB drive | ||
| + | - For F270: | ||
| + | - The F270 the printer will print a raft before printing the model. Make sure first layer is set to support material or removal will be incredibly difficult. | ||
| + | - Send job to F270 over Ethernet | ||
| + | - Record the material used and print time in the online log along with the other job information requested. The print log should be on the desktop or https:// | ||
| + | | ||
| + | - Ultimaker: | ||
| + | - Make sure print bed is clean | ||
| + | - F270: | ||
| + | - Make sure that there is enough room on an CLEAN build tray for your part, and that the build tray is secured in the printer | ||
| + | | ||
| ====Part Removal and Cleaning==== | ====Part Removal and Cleaning==== | ||
| - | Ultimaker | + | **Ultimaker** |
| - | * Remove part from print bed using a spatula or razor being careful not to cut yourself or scratch the build plate. Make sure no body part is in line with the tool should it slip or the part break free unexpectedly.\\ | + | * Remove part from print bed using a spatula or razor being careful not to cut yourself or scratch the build plate. Make sure no body part is in line with the tool should it slip or the part break free unexpectedly. |
| - | F270 | + | * If support was used, submerge print in warm water for several hours to dissolve PVA filament. (prints can warp if submerged in water for over 24 hours) |
| + | **F270** | ||
| * Don gloves, face shield, and lab coat | * Don gloves, face shield, and lab coat | ||
| * Carefully, slowly and without splashing cleaning solution open the support removal tank lid, remove and open the tank | * Carefully, slowly and without splashing cleaning solution open the support removal tank lid, remove and open the tank | ||
| Line 110: | Line 123: | ||
| ABS: .12/gram | ABS: .12/gram | ||
| ----- | ----- | ||
| - | =====Quick Review===== | + | =====Ultimaker 3 Quick Review===== |
| Tool Lead: Andrew Furst \\ | Tool Lead: Andrew Furst \\ | ||
| Contact: Andrewfurst@ucsb.edu | Contact: Andrewfurst@ucsb.edu | ||
| Line 138: | Line 151: | ||
| * Filament should be dried before use if printer has been idle for several weeks | * Filament should be dried before use if printer has been idle for several weeks | ||
| * Bed leveling should be completed every time print cores are swapped | * Bed leveling should be completed every time print cores are swapped | ||
| - | * Print cores should be swapped after clog or to change print line width. Used print heads should be kept for spare parts | + | * Print cores should be swapped |
| ----- | ----- | ||
| + | |||
| + | [[ruler]] | ||
ultimaker_3_sop.1598469276.txt.gz · Last modified: 2020/08/26 19:14 by furst